Re: Joyetech Cuboid TC
Napísal: Pia 08. Apr 2016 18:24:18No .. kolega si ho kupi..sa rozhodol potom ako som mu povedal ZA/Proti ..
kazdopadne je navratnost /unho /1 mesiac po prechode na vaping..
Ked si predstavim,ze EVic VTC mini je prcek..tak Cubo mini je este mensi prcek..
Co sa tyka beterie -to sa uvidi,az ked sa to dakomu podari rozobrat a zistit ci sa DA/Neda ta bateria vymenit..
Ale zamna,ked sa da cejncnut na eGo baterke akumulator-tak aj tu..sa bude dat./len treba el.tech znalosti
aspon spajkovanie.
Ked to kolegovi Prijde.. hnet to vysetrim mozno pofotim s EVicom.
kazdopadne je navratnost /unho /1 mesiac po prechode na vaping..
Ked si predstavim,ze EVic VTC mini je prcek..tak Cubo mini je este mensi prcek..
Co sa tyka beterie -to sa uvidi,az ked sa to dakomu podari rozobrat a zistit ci sa DA/Neda ta bateria vymenit..
Ale zamna,ked sa da cejncnut na eGo baterke akumulator-tak aj tu..sa bude dat./len treba el.tech znalosti
aspon spajkovanie.
Ked to kolegovi Prijde.. hnet to vysetrim mozno pofotim s EVicom.
[Odkryť] Spoiler:
Specifications:
Dimension Size: 22.50 x 35.50 x 76.50mm;
Battery Capacity: 2400mAh;
Output Mode: VT-Ti/VT-Ni/VT-SS316/VW/BYPASS/TCR Mode;
Output Wattage: 1-80W;
Resistance Range for VT mode: 0.05-1.5ohm;
Resistance Range for VW/BYPASS mode: 0.1~3.5ohm;
Temperature Range: 100~315'C / 200~600'F;
510 stainless steel thread;
Wide border fitting for large capacity atomizers;
Colors: Black, Silver, Grey, White, Gold
Dual Circuit Protection:
Joyetech Cuboid Mini applies two sets of battery protection circuit system, realizing overall battery protection of over-charging, over-current and over-discharging, which makes it more safe and reliable.
Firmware Upgradeable:
Cuboid Mini comes with the upgradeable firmware.
Having Version 3.00 for Cuboid Mini, Temp-SS316 and customized TCR are available.
Customized TCR Available:
Joyetech Cuboid Mini enables you to adjust TCR values for different materials, thus further improving the accuracy of temperature control and bringing you the great taste.
There are three options (M1, M2, M3) for you to customize the TCR according to the material.
In power-off condition, press the fire button and the right regulator simultaneously for around 5 seconds, then you enter into the TCR set menu. And you can find the TCR Value Range for your reference.
Bottom Ventilation Holes:
The ventilation holes are placed on the bottom which can greatly help the device for better heat dissipation.
Note: Should you get stuck while upgrading, just press the "+" button and then insert into the reset hole with a needle to restart.
Charging & Upgrading:
The micro USB port is on the top of the left side. Connect it with a micro USB cable to charge or upgrade your device. The charging indicator will go out When it's fully charged.
Dimension Size: 22.50 x 35.50 x 76.50mm;
Battery Capacity: 2400mAh;
Output Mode: VT-Ti/VT-Ni/VT-SS316/VW/BYPASS/TCR Mode;
Output Wattage: 1-80W;
Resistance Range for VT mode: 0.05-1.5ohm;
Resistance Range for VW/BYPASS mode: 0.1~3.5ohm;
Temperature Range: 100~315'C / 200~600'F;
510 stainless steel thread;
Wide border fitting for large capacity atomizers;
Colors: Black, Silver, Grey, White, Gold
Dual Circuit Protection:
Joyetech Cuboid Mini applies two sets of battery protection circuit system, realizing overall battery protection of over-charging, over-current and over-discharging, which makes it more safe and reliable.
Firmware Upgradeable:
Cuboid Mini comes with the upgradeable firmware.
Having Version 3.00 for Cuboid Mini, Temp-SS316 and customized TCR are available.
Customized TCR Available:
Joyetech Cuboid Mini enables you to adjust TCR values for different materials, thus further improving the accuracy of temperature control and bringing you the great taste.
There are three options (M1, M2, M3) for you to customize the TCR according to the material.
In power-off condition, press the fire button and the right regulator simultaneously for around 5 seconds, then you enter into the TCR set menu. And you can find the TCR Value Range for your reference.
Bottom Ventilation Holes:
The ventilation holes are placed on the bottom which can greatly help the device for better heat dissipation.
Note: Should you get stuck while upgrading, just press the "+" button and then insert into the reset hole with a needle to restart.
Charging & Upgrading:
The micro USB port is on the top of the left side. Connect it with a micro USB cable to charge or upgrade your device. The charging indicator will go out When it's fully charged.
v teamovej sucinnosti..gif "plač")
